Fast-Vac™ SC-Series™ Self Contained Vacuum Loader Shuttles…
Fast-Vac Industrial Vacuum Loader Shuttle

 

 

are heavy-duty, powerful, efficient, and dust free industrial vacuum modules, integrally mounted on a hook lift shuttle for vacuum removal of virtually any dry material, sludges, slurries, and liquids from remote or inaccessible locations. It is easy to maneuver for a one man operation.  These heavy duty Industrial vacuum loaders have a wide range of other applications. The Fast-Vac™ Model R1.2S is a heavy-duty, powerful, efficient, and dust free industrial vacuum module, suitable to be picked up by a separate truck with a hydraulic tilting bed, winch, and hook. The shuttle can be dropped, used to vacuum  up virtually any dry material, sludge, slurries, and liquids from remote or inaccessible locations. It is easy to maneuver for a one man operation, and picked up when the hopper is full. You do not tie up a truck during the vacuuming phase.

This self-contained unit  is equipped with a hook lift offloading system for convenient transport on a trailer, chassis or other transport system. This vacuum module is designed to be used with a truck with a hydraulic tilting bed, a winch and hook. The truck would be similar to those used to pick up roll-off boxes.

Each unit can come completely equipped with many options such as the Fast–Vac™ Hydro package including a 270 degree articulating boom. A high-pressure washer system powered by a 3500 P.S.I. Hydraulic Cat Pump.

SC-Series™ Photo Gallery

SC-Series™ IVL Specifications

Vacuum Pump

The Model R1.2S has a positive displacement rotary lobe vacuum pump for 1245 icfm at 16” Hg at standard temperature and pressure.

Pump has a discharge silencer.

Pump is isolated from the frame by rubber isolator mounts.

Drive

Transfer case with air shift. Transfer case is isolated from the frame by rubber isolator mounts.

6 Cu. Yd. Collection Hopper

  • 6 cubic yard total (dry material)

Tailgate

Hydraulic over mechanical for open, close, lock, and unlock mechanisms. D-ring style gasket assures proper sealing for liquids.

Hydraulics

Transmission mounted PTO with hydraulic pump of adequate capacity and pressure rating. Necessary spool valves and circulation system of adequate capacity and pressure rating.

Filtration System

The filter bags are Teflon coated and the bag house will have an air to cloth ratio of 4.6 to 1 with 60 filter bags at 1245 icfm. Bags are installed with a “Snap Ring” retaining system. Filter cleaning is continuous and is accomplished by a programmed timed pulse of compressed air. Filter cleaning by the system air compressor maintains 100 psi with air tank. Filter bags are cleaned by a reverse pulse jet to the diaphragm valve controlled by a solid state sequencing timer contained in a NEMA 4 enclosure.

 

Controls

Controls are provided for shifting the transfer case, setting the engine throttle and reverse pulse jet system. Hydraulic controls are located above the truck frame for ease of operation and adequate ground clearance.

Instrumentation, 12 Volt DC

Driver Side Controls include:

Tachometer, hour meter, and air pressure gauge.

Hydraulic dual lever, one for unlock and lock and one for opening and closing of rear tailgate.

Dust tight push buttons for Vacuum start and Vacuum Stop.

Digihelic differential pressure controller.

Vacuum Gauge with “O” seal.

Collector Body

Bag house will dump with the collector body.

Filtration system is of parallel design and is a dual mode which requires switching from dry mode to wet mode or
visa versa. Payload capacity is 6 cubic yards gross. Body is loaded through a 5” rear port via a deflector target plate inside the body.

The safety of the people working with or on the equipment is of primary concern and safely protected. Rear ladder for roof access and to filter baghouse. Top of baghouse and collector body has non-skid surface and side rails.

Miscellaneous

Two 2 1/2” Vacuum Relief Valves
Wet/Dry Level Probe
5” Vacuum Breaker, all fault opens vacuum breaker

Maintenance

Unit is designed for ease of maintenance. The unit has the proper hose and pipe sizing chart for various bulk densities and conveying distances attached. The unit also incorporates commonly manufactured components for ease of replacement of parts and service. CD is provided of the Operating and Maintenance manual.

Quality

The vacuum module is manufactured with industry standard components. The unit is welded by certified welders to assure the highest quality. The unit incorporates all new components. No remanufactured or used parts are  used. Unit is quoted with Rust-Oleum High Gloss Polyester Urethane in Fast-Vac White

 

 

Fast-Vac™ reserves the right to change specifications without notice. Download Spec Sheet

 

Call us for more information on the SC-Series™ Industrial Vacuum Loader

1-800-558-2280